Roll cages and half cages: what they do and what they cost a road car

The biggest safety upgrade for serious track use, and the biggest compromise on the road. Harness bars, half cages, bolt-in and weld-in cages compared.

Generate photorealistic automotive lifestyle UK-based

A roll cage is the single biggest safety upgrade for a car that sees serious track use. It protects the cabin if the car rolls or hits something hard, stiffens the shell and provides strong mounting points for harnesses. It also changes how practical the car is on the road. Here is what each type of cage does and how to decide whether you need one.

What a cage does

A road car’s roof and pillars are not designed to hold the car’s weight in a roll. A cage adds a structure of steel tubes inside the cabin that keeps the space around the occupants intact. A well-designed cage also connects the front and rear suspension mounting areas, which stiffens the shell and makes the suspension work more consistently.

Types of cage

Type Structure Protection Road practicality Typical use
Harness bar Single bar behind the seats None in a roll, mounting point only Good, rear seats usually lost Track day cars with harnesses
Half cage (rear) Main hoop and backstays Some roll protection behind the driver Fair, rear seats lost Track day and some sprint cars
Bolt-in full cage Front and rear hoops, bolted to the floor Good Poor, harder access Club competition, removable if needed
Weld-in full cage Welded to the shell at many points Excellent, stiffest structure Poor Racing and rallying

Bolt-in or weld-in?

A bolt-in cage attaches to the floor and sills with spreader plates and bolts. It can be fitted and removed without welding, which makes it attractive for cars that may return to standard. A weld-in cage is welded to the shell at more points, often including the roof pillars. It is stiffer and stronger, but permanent.

For competition, the regulations decide for you. Motorsport UK sets out its requirements for roll-over protection in the National Competition Rules, which cover tube sizes, mounting methods and the configurations allowed for each type of event. Check the rules for your championship before ordering a cage.

Read the rules for the series you want to enter before the cage goes in, not after.

Dan Whitlock

Living with a cage on the road

  • Head injuries. Without a helmet, hitting a cage tube is dangerous. Any tube within reach of your head should be covered with proper roll cage padding, and even then the risk does not go away. This is why many people stop short of a full cage on road cars.
  • Access. Door bars make getting in and out harder. Some cages use swing-out or removable door bars to help.
  • Seats. Most cages mean losing the rear seats. Update the seating capacity on the V5C with the DVLA if the number of seats changes.
  • Noise and comfort. A stiffer shell passes more noise and vibration into the cabin, especially with a stripped interior.

Fitting

A cage only protects you if it is fitted properly. Bolt-in cages need spreader plates of the right size and the correct grade of bolts. Weld-in cages should be built or fitted by an experienced specialist, because poor welds and incorrect mounting can make a cage less safe than none. For competition, ask the fitter to confirm the cage meets the regulations, and keep the paperwork for scrutineering.

Harness bars and half cages

If you are fitting a harness, read our guide to bucket seats and harnesses first.

For many track day drivers, a harness bar or half cage is the sensible middle ground. It gives a correct mounting point for harness shoulder straps, adds some stiffness and, with a half cage, some protection behind the driver, while keeping the car usable on the road. A harness bar on its own does not protect you in a roll, so treat it as a mounting point, not a safety structure.

Insurance

A roll cage is a significant modification. Declare it to your insurer, and if the car is used for competition, check whether your policy covers events. Many road policies exclude any use on a track.

Dan Whitlock

Wheels editor

Dan has been fitting, refurbishing and arguing about wheels since 2009. He drives the E46 every day and owns more wheel cleaner than any one person should.

More from Dan
Next story

Approved LED bulbs can now pass the MOT, but read the small print

From 14 October, some approved LED replacement bulbs can pass the MOT in halogen lamps. Only two bulb types qualify so far, and the sticker matters as much as the bulb.

Read it
Approved LED bulbs can now pass the MOT, but read the small print
More in Interior