Exhaust materials and pipe sizing: why bigger isn’t always better

Mild steel, 304 stainless or titanium, and how big the pipe should be. Why oversized exhausts can cost torque on naturally aspirated engines.

Generate photorealistic automotive lifestyle UK-based

When people plan an exhaust upgrade, they usually think about sound. The material the system is made from and the diameter of the pipe matter just as much. Together they decide how long the exhaust lasts through British winters, how much weight it saves and whether it adds power or quietly takes some away.

Materials

Material Corrosion resistance Weight Cost Notes
Mild steel, aluminised Fair, rusts from the inside out Heavy Low Most factory systems
409 stainless Good, may develop surface rust Moderate Moderate Common on factory and budget sports systems
304 stainless Very good, stays bright with cleaning Moderate Moderate to high The standard for quality aftermarket systems
Titanium Excellent Very light Very high Track cars and premium systems, distinctive tone
Inconel Excellent at very high temperatures Light, thin wall Extremely high Motorsport manifolds and turbo systems

For a UK road car, 304 stainless steel is usually the sweet spot. It shrugs off road salt, lasts many years and is affordable compared with titanium. Many quality systems come with a lifetime or long warranty against corrosion.

Titanium saves a lot of weight, which matters on a track car or lightweight sports car. It also gives a harder, more metallic sound. It costs much more and can be difficult to repair if damaged.

Why bigger is not always better

It is tempting to think a bigger pipe always flows better. Up to a point, it does. Beyond the size an engine needs, a larger pipe slows the exhaust gas down. On a naturally aspirated engine, the speed of the gas helps pull spent gases out of the cylinders through an effect called scavenging. Slow the gas too much and you can lose low and mid-range torque, which is the part of the rev range you use most on the road.

Turbocharged engines are different. The turbo breaks up those pressure pulses, and after the turbo, lower back pressure generally helps the turbo spin up and flow. That is why bigger downpipes and turbo-back systems suit tuned turbo cars, while a modest cat-back is usually the better choice on a naturally aspirated engine.

Engine Pipe size approach Why
Small naturally aspirated Close to standard, smooth bends Keeps gas speed and low-down torque
Large naturally aspirated Modest increase, tuned manifold Balance of top-end flow and torque
Standard turbo Moderate increase after the turbo Lower back pressure helps the turbo
Tuned turbo Larger downpipe and system, matched to the map Higher flow needed for more boost

The best exhaust for most road cars is the one that is barely bigger than standard, but much better made.

Dan Whitlock

Construction details that matter

  • Mandrel bends. Pipes bent on a mandrel keep their full diameter round corners. Crush bends narrow the pipe and add restriction.
  • Welds. Neat, consistent welds with back purging on stainless systems resist cracking and corrosion.
  • Hangers and flexible joints. Proper rubber hangers and a flexi section reduce vibration and stop cracks forming.
  • Silencer packing. Absorptive silencers use packing that can break down over time, making the system louder. Good systems use durable packing and can sometimes be repacked.

Drone

Drone is a low booming noise at a steady motorway speed. It is caused by the exhaust resonating at a frequency that matches the engine’s speed at cruise. It is the most common complaint about aftermarket systems and is hard to judge from a video. Resonated systems and those with valves that close at cruise reduce drone. If you do a lot of long journeys, ask for feedback from owners of the same car.

Heat and clearance

Larger pipes need more room. Check clearance around the floor, fuel tank, subframe and heat shields, especially on lowered cars. Keep or replace the heat shields, because the floor above an exhaust can get very hot.

Care

Stainless and titanium tips stay looking good with a regular clean using a metal polish. In winter, rinse salt off the underside of the car when you wash it. Even stainless lasts longer when it is not caked in road salt all season.

Dan Whitlock

Wheels editor

Dan has been fitting, refurbishing and arguing about wheels since 2009. He drives the E46 every day and owns more wheel cleaner than any one person should.

More from Dan
Next story

Oil coolers: when you need one and how to fit one properly

Track days and big power push oil temperatures up. How to tell if you need an oil cooler, why the thermostat matters and how to mount it.

Read it
Oil coolers: when you need one and how to fit one properly
More in Exhausts