Thermostats, fans and coolant: engine cooling basics for modified cars

Before buying a bigger radiator, get the basics right. How the thermostat, fans, coolant and pressure cap work, and the signs of trouble.

Generate photorealistic automotive lifestyle UK-based

Engine cooling is the system most modifiers ignore until something goes wrong. It is not glamorous, but it decides whether a tuned engine lasts. Before spending money on bigger radiators and racing cooling kits, it pays to understand the basics: the thermostat, the fans, the coolant and the pressure cap. Get those right and many overheating problems never happen.

How the system works

The water pump pushes coolant through passages in the engine block and head, where it picks up heat. The thermostat decides when the coolant flows to the radiator. Air passing through the radiator, pushed by the car’s speed or pulled by the fans, carries the heat away. The pressure cap keeps the system pressurised, which raises the boiling point of the coolant.

The thermostat

The thermostat is a valve that stays closed while the engine is cold, so it warms up quickly, then opens to let coolant flow through the radiator. A thermostat stuck open makes the engine run cold, wastes fuel and increases wear. One stuck closed causes rapid overheating.

Lower-temperature thermostats are popular in tuning circles. They open earlier and can help on track. On a road car, especially a modern one, running cooler than designed can hurt economy, increase wear and upset the ECU, which uses coolant temperature to calculate fuelling. For most road cars, a fresh standard thermostat is the right choice.

Part What it does Common faults Signs
Thermostat Controls flow to the radiator Sticks open or closed Slow warm-up, or sudden overheating
Water pump Circulates coolant Worn impeller, leaking seal Overheating, coolant weeping from the pump
Radiator fans Pull air through the radiator at low speed Failed motor, relay or sensor Overheating in traffic but fine when moving
Pressure cap Holds system pressure Worn seal Coolant loss, boiling over
Hoses Carry coolant Perished rubber, swelling, splits Leaks, soft or bulging hoses
Coolant Carries heat, prevents freezing and corrosion Old, wrong type, wrong mix Discoloured coolant, corrosion, overheating

Fans

At speed, the car’s movement pushes plenty of air through the radiator. In traffic, at a show or in the pits, the fans do all the work. A car that overheats in traffic but is fine on the move usually has a fan problem: a failed motor, relay, fuse or temperature switch.

Upgraded fans with a proper shroud cover more of the radiator and move more air. A shroud matters more than people think, because a fan without one only pulls air through the circle it sweeps.

Coolant

Coolant is a mix of antifreeze and water. The antifreeze stops freezing in winter, raises the boiling point and, just as importantly, protects the engine and radiator from corrosion. Plain water cools well but offers no protection and should not be used on a road car.

  • Use the right type. Different manufacturers specify different coolant chemistries. Colour is not a reliable guide, so check the handbook or the coolant maker’s application list.
  • Mix correctly. A 50/50 mix is typical for the UK. More antifreeze does not mean better cooling.
  • Change it on schedule. Corrosion inhibitors wear out, even if the coolant looks fine.

Fresh coolant, a good cap and working fans fix more overheating than any radiator.

Tom Barker

The pressure cap

Pressurising the cooling system raises the boiling point of the coolant. A worn cap lets the pressure escape, the boiling point drops, and the car can boil over well below its normal limit. Caps are cheap and worth replacing when changing coolant. Higher-pressure caps exist, but use them carefully on older cars, because more pressure puts more strain on hoses and radiators.

Bleeding the system

Air trapped in the cooling system causes hot spots and erratic temperature readings. After draining coolant, follow your car’s bleeding procedure. Some engines have bleed screws at high points, others need the front of the car raised. Run the engine with the heater on hot, top up as the level drops, and recheck after the first few drives.

Signs of trouble

  • Coolant level dropping with no visible leak, which may point to a head gasket.
  • Sweet smell from the engine bay or cabin.
  • White smoke from the exhaust once warm.
  • Heater blowing cold when the engine is hot.
  • Temperature gauge moving when it normally stays still.

Never open the cap on a hot engine. The coolant is under pressure and can cause serious burns.

Tom Barker

Tech & events

Tom writes the fitment explainers and spends most summer weekends at shows with a notebook and a tape measure.

More from Tom
Next story

Bucket seats and harnesses for track days: a buyer’s guide

Sliding around in a standard seat makes a car harder to drive quickly. Choosing a bucket seat and harness, mounting them properly and keeping the car road legal.

Read it
Generate photorealistic automotive lifestyle UK-based
More in Cooling